Showing 1–16 of 54 results
-
Part No. 113545
Designed for viscous or thick liquid sampling where accuracy and sample integrity are essential, these sterile two-inch, 14-gauge side-hole needles are ideal for pulling inline samples through QualiTru® TruStream7™ and TruStream12™ stainless steel ports. Each wide-gauge, pre-sterilized needle features a point-tip design for smooth insertion through septa, consistent flow, and representative sample collection, while avoiding coring issues that may occur with standard bevel-tip needles.
Key Features
-
14-gauge, 2-inch side-hole needle for reliable, accurate sampling
-
Point-tip design aids clean, controlled insertion through septa
-
Pre-sterilized and individually packaged for aseptic handling and convenience
Key Benefits
- Preserves sample integrity and minimizes contamination risk
- Improves sampling efficiency for viscous or thick liquid products
- Eliminates coring issues that may occur
-
Part No. 113555
Our 14-gauge Side-Hole Needle is designed for viscous liquid sampling where accuracy and sample integrity are essential. Each wide-gauge, pre-sterilized needle features a point-tip design for smooth insertion through septa and a single side hole for consistent flow and representative sample collection.
Key Features
-
14-gauge, 4-inch side-hole needle for reliable, accurate sampling
-
Point-tip design aids clean, controlled insertion through septa
-
Pre-sterilized and individually packaged for aseptic handling and convenience
Key Benefits
- Preserves sample integrity and minimizes contamination risk
- Improves sampling efficiency for viscous or thick liquid products
-
Part No. 241010
The TruStream3 NPS Drum Sampling Cap is designed to replace a standard NPS bung plug. Its integrated three-channel septum, injection-molded directly into the cap, enables fast and hygienic sampling through a 4-inch, 14-gauge side-hole needle to assess product quality and composition without exposing contents to airborne contaminants.
*Contact QualiTru for product compatibility information.
-
Part No. 211125, 211129, 211133 & 211137
The Tri-Clamp Port is designed to be tri-clamped in place, inline, or on a silo to allow quick access for process sampling. Available in 1.5″, 2″, 2.5″, and 3″.
-
Part No. 212113
The Tank Port is designed for taking aseptic samples off a silo. It can be welded onto a flat, non-insulated tank door.
-
Part No. 212123, 212127 & 212133
The Recessed Tank Port is designed for taking aseptic samples off a silo. It can be welded onto a flat or slightly curved insulated tank door.
-
Part No. 213019, 213025, 213029, 213033 & 213037
The Tri-Clamp Elbow Port replaces standard tri-clamp elbows to quickly take aseptic samples.
-
Part No. 213075, 213079, 213083 & 213087
The Butt Weld Elbow Port allows for permanent inline sampling by welding the elbow in place.
-
Part No. 215075, 215077, 215079 & 215085
The Butt Weld Tee Port allows for permanent inline sampling by welding the straight tee in place.
-
Part No. 215145 & 215147 & 215151
The Tri-Clamp Tee Port replaces a standard tri-clamp straight tee to quickly take aseptic samples.
-
Part No. 215515, 215520 & 215525
This Short Tee port replaces a short tri-clamp straight tee to quickly take aseptic samples.
-
Part No. 212533
The TS7 Adjustable Tanker Port with Security Lid is specifically designed for dairy and other liquid food tanker trucks. It welds onto the inner tank wall and the sliding telescopic sleeve design minimizes the need for additional retrofitting and fabrication. The port accommodates trailers with varying thicknesses of insulation (from ~4.3” to 6.0”). This port is ideal for sampling off the side or back of a tanker truck for accurate and safe antibiotic, component, or microbiological sampling.
-
Part No. 214500
The Inline Inspection Port is for use at VARIVENT® connection points.
-
Part No. 217105
The QualiTru Ingold Port revolutionizes bioreactor sampling and inoculation by eliminating the need for Steam in Place (SIP) between samples, increasing efficiency and minimizing risk in critical process applications.
-
Part No. 211164, 211168, 211174, & 211184
The Tri-Clamp Port is designed to be tri-clamped in place, inline, or on a silo to allow quick access for process sampling.
-
Part No. 217301
This is used to secure the septum in place in the TS7 Ingold Port. It comes standard with the TS7 Ingold port but can be purchased separately to replace the TS7 Ingold nut. A TruStreem7 plastic dust cover can be used to protect the stainless steel port when not sampling.
